Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Dust, smudges, or lint present on the resin 3D printer's LCD surface may affect printing. In order to increase your success rate in resin 3D printing, we recommend you keep your LCD printing screen clean at all times.
Method 1
Dry Cleaning: Use a dust-free cloth to gently remove all visible dust and lint from the surface of your resin 3D printer’s LCD printing screen.
Method 2
Wet Cleaning: Spray a small amount of 95% sanitizing alcohol on the printer's LCD to remove any cured resin, smudges, or fingerprints present on the LCD. Use a soft kitchen paper towel or a dust-free cloth and wipe in one direction to clean the surface of the LCD printing screen thoroughly.

Resin can be stored in resin tanks for up to three months under closed conditions. Storing longer than the recommended time may cause resin to leak and damage equipment.
If the printer is not used for a long time, don't leave excess resin in the vat as this might lead to resin curing which will affect the next printing. The resin that is in the tank after a print can be reused, but it is recommended to filter into a new container and not return to the cartridge to avoid potential contamination.

Magforms has not performed testing on gas permeability of our materials. Parts printed on Magforms LCD printers are water-tight and non-porous if they are printed as a sealed, continuous structure.

For information about the material properties of Magforms resins, consult the Technical Data Sheets (TDS).
To learn more about specific resins and their applications, read the product details page choosing the right material.

Unless specifically indicated, Magforms resin is not approved for use with food, drink, or for medical application on or in the human body. Do not attempt to use printed parts for purposes other than the described application.